General Specifications

NT40E3-4-PTP-NEBS Installation

product_line_custom
Napatech SmartNIC
category
Hardware Installation Guide

Network interface

Characteristic Description
IEEE standards

IEEE 802.3 10 Gbit/s Ethernet

IEEE 802.3 100 Mbit/s FDX / 1 Gbit/s Ethernet

Type of physical interface SFP+
Number of physical interfaces 4 ports
Supported pluggable modules

SFP+

SFP

Pluggable Modules

For information on modules that have been qualified by Napatech for use with the SmartNIC, see accessories.napatech.com.

Host interface

Characteristic Description
Bus type PCI Express Gen3
Bus width 8-lane
Bus speed 8 GT/s
PCIe controller Based on a PCI Express IP core integrated in the FPGA
Data transfer mode Memory write or memory read transactions
Data width Support for 32/64-bit addressing and data width
Interrupt Support for Message Signaled Interrupts (MSI) or legacy interrupts

Physical dimensions

Characteristic Description
PCIe length 1/2-length
PCIe height Full-height
PCIe width Single-slot

This list shows the PCIe standard dimensions:

  • 1/2-length: 167.65 mm (6.600 inches)
  • Full-height: 111.28 mm (4.381 inches)
  • Single-slot:
    • Top: 14.47 mm (0.570 inches)
    • Bottom: 2.67 mm (0.105 inches)

Environment

Characteristic Description

Operating temperature

–5 °C to 55 °C (23 °F to 131 °F) measured around the SmartNIC.
Note: The SmartNIC requires a laminar air flow along the board for operation up to 55 °C.

Operating relative humidity

5% to 85%

Compliances

  • NEBS Level 3
  • PCI-SIG®
  • CE (EU)
  • CB
  • RoHS
  • REACH
  • cURus(UL)
  • FCC (USA)
  • CSA (Canada)
  • VCCI (Japan)
  • RCM (Australia)

MTBF

Characteristic Description
MTBF 367,807 hours (42 years)
Standard According to UTE C 80-810

Electrical rating

This table shows the power consumption for an NT40E3-4-PTP-NEBS SmartNIC including 4 × 10GBASE-SR SFP+ modules.

Auxiliary Power Connector Used Supply Voltage Supply Current Supply Power
PCI Express Aux. Power PCI Express Aux. Power PCI Express Aux. Power Total Max.

3.3 V

[in V]

12 V

[in V]

12 V

[in V]

3.3 V

[in A]

12 V

[in A]

12 V

[in A]

3.3 V

[in W]

12 V

[in W]

12 V

[in W]

[in W]

No 3.3 12 - 1.5 1.8 - 4.9 22.1 - 27
Yes 3.3 12 12 1.5 - 1.8 4.9 - 22.1 27

The SmartNIC is Class III equipment for supply by SELV circuits only.

Port numbers

Characteristic Description
Port numbers 0, 1, 2 and 3
Location
NT100E3-1-PTP/ NT200C01-SCC showing ports 0,1, 2 and 3

RAM bank

Characteristic Description
Flash Supports two boot images
Memory 4 GB DDR3 RAM bank
Memory details Standard 64-bit DDR3-1866 RAM bank

Expansion connectors

The expansion connectors are reserved for future use.

Characteristic Description
Connectors Two 50-pin expansion connectors. Each expansion connector contains 4 serial high-speed links running at up to 11.3 Gbit/s. This provides a total maximum bidirectional bandwidth of 40 Gbit/s.
Location
NT40E3-4-PTP-NEBS showing expansion connectors 0 and 1