General Specifications

NT20E3-2-PTP Installation

Platform
Napatech SmartNIC
Content Type
Hardware Installation Guide

Network interface

Characteristic Description
IEEE standards

IEEE 802.3 10 Gbit/s Ethernet

IEEE 802.3 100 Mbit/s FDX / 1 Gbit/s Ethernet

Type of physical interface SFP+
Number of physical interfaces 2 ports
Supported pluggable modules

SFP+

SFP

Pluggable Modules

For information on modules that have been qualified by Napatech for use with the SmartNIC, see accessories.napatech.com.

Host interface

Characteristic Description
Bus type PCI Express Gen3
Bus width 8-lane
Bus speed 8 GT/s
PCIe controller Based on a PCI Express IP core integrated in the FPGA
Data transfer mode Memory write or memory read transactions
Data width Support for 32/64-bit addressing and data width
Interrupt Support for Message Signaled Interrupts (MSI) or legacy interrupts

Physical dimensions

Characteristic Description
PCIe length 1/2-length
PCIe height Full-height
PCIe width Single-slot

This list shows the PCIe standard dimensions:

  • 1/2-length: 167.65 mm (6.600 inches)
  • Full-height: 111.28 mm (4.381 inches)
  • Single-slot:
    • Top: 14.47 mm (0.570 inches)
    • Bottom: 2.67 mm (0.105 inches)

Environment

Characteristic Description

Operating temperature

0°C to 45°C (32°F to 113°F) measured around the SmartNIC

Operating relative humidity

20% to 80%

Compliances

  • PCI-SIG®
  • CE (EU)
  • CB
  • RoHS
  • REACH
  • cURus(UL)
  • FCC (USA)
  • CSA (Canada)
  • VCCI (Japan)
  • RCM (Australia)
  • KCC (Korea)

MTBF

Characteristic Description
MTBF 297,993 hours (34 years)
Standard According to UTE C 80-810

Electrical rating

This table shows the power consumption for an NT20E3-2-PTP SmartNIC including 2 × 10GBASE-SR SFP+ modules.

Auxiliary Power Connector Used Supply Voltage Supply Current Supply Power
PCI Express Aux. Power PCI Express Aux. Power PCI Express Aux. Power Total Max.

3.3 V

[in V]

12 V

[in V]

12 V

[in V]

3.3 V

[in A]

12 V

[in A]

12 V

[in A]

3.3 V

[in W]

12 V

[in W]

12 V

[in W]

[in W]

No 3.3 12 - 1.5 1.8 - 4.9 22.1 - 27
Yes 3.3 12 12 1.5 - 1.8 4.9 - 22.1 27

The SmartNIC is Class III equipment for supply by SELV circuits only.

Port numbers

Characteristic Description
Port numbers 0 and 1
Location
Port_Numbers Sheet.1 Sheet.2 Port 0 Port 0 Sheet.3 Sheet.4 Port 1 Port 1 Sheet.9

RAM bank

Characteristic Description
Flash Supports two boot images
Memory 4 GB DDR3 RAM bank
Memory details Standard 64-bit DDR3-1866 RAM bank

Expansion connectors

The expansion connectors are reserved for future use.

Characteristic Description
Connectors Two 50-pin expansion connectors. Each expansion connector contains 4 serial high-speed links running at up to 11.3 Gbit/s. This provides a total maximum bidirectional bandwidth of 40 Gbit/s.
Location
High_speed_exp_connectors Sheet.1 Sheet.7 Expansion connectors Expansion connectors Sheet.8 Sheet.9