errorcodes.h
Go to the documentation of this file.
129 NT_MAKE_ERROR3(NT_ERROR_PORT_OUT_OF_RANGE, "Port out of range", "Port %d out of range. Range is [0..%d].\n") \
130 NT_MAKE_ERROR3(NT_ERROR_IPPROTOCOL_OUT_OF_RANGE, "IpProtocol out of range", "Protocol %d out of range. Range is [0..%d].\n") \
131 NT_MAKE_ERROR3(NT_ERROR_ADAPTER_OUT_OF_RANGE, "Adapter out of range", "Adapter%d out of range. Range is [0..%d].\n") \
136 NT_MAKE_ERROR2(NT_ERROR_UNSUPPORTED_SEQUENCE, "The sequence, in which the commands are issued, is illegal on this adapter") \
145 NT_MAKE_ERROR2(NT_ERROR_TIMESTAMP_VS_HDR_MISMATCH, "Detected a time stamp type setting and packet descriptor type setting mismatch") \
156 NT_MAKE_ERROR2(NT_ERROR_OS_DMA_STILL_MAPPED, "Failed to release DMA buffer - need to unmap before releasing") \
165 NT_MAKE_ERROR2(NT_ERROR_OS_FLOCKEND_INVALID_PARAM, "FastLockEnd called with invalid parameter") \
168 NT_MAKE_ERROR2(NT_ERROR_OS_IRQ_EVENT_WAIT_PARAM, "IRQEventWait called with invalid parameter") \
169 NT_MAKE_ERROR2(NT_ERROR_OS_NAMED_EVENT_INVALID_PARAM, "NamedEvenCreate called, but named events not yet created") \
170 NT_MAKE_ERROR2(NT_ERROR_OS_NAMED_EVENT_MAXED_OUT, "NamedEvenCreate called, but no more events available") \
180 NT_MAKE_ERROR2(NT_ERROR_32_64_BIT_MISMATCH, "A 32bit/64bit mismatch between ntservice and NTAPI") \
184 NT_MAKE_ERROR2(NT_ERROR_BONDING_SLAVE_TS_NO_CONFIG, "Bonding Slave misses timesync configuration") \
185 NT_MAKE_ERROR2(NT_ERROR_BONDING_MASTER_NO_TS_SYNC, "Bonding Master failed initial time synchronization") \
186 NT_MAKE_ERROR2(NT_ERROR_BONDING_SLAVE_NO_TS_SYNC, "Bonding Slave failed initial time synchronization") \
189 NT_MAKE_ERROR2(NT_ERROR_EVENT_RAISE_NOT_ACTIVE, "Raising events not activated. Specify a listen event on open") \
194 NT_MAKE_ERROR3(NT_ERROR_GROUP_OUT_OF_RANGE, "GroupId out of range", "GroupId %d out of range. Range is [0..%d].\n") \
195 NT_MAKE_ERROR2(NT_ERROR_DESCR_BIT_POSITION_OUT_OF_RANGE, "The descriptor bit position is out of range") \
196 NT_MAKE_ERROR2(NT_ERROR_TX_DESCR_MODE_UNKNOWN, "The chosen TX descriptor is unknown or unsupported") \
201 NT_MAKE_ERROR2(NT_ERROR_DRIVER_AND_NTAPI_VERSION_MISMATCH, "Mismatch of driver and NTAPI libraries") \
215 NT_MAKE_ERROR2(NT_ERROR_SLICEOFFSET_ZERO, "SliceOffset cannot be 0 without a SliceAddHeader option") \
226 NT_MAKE_ERROR2(NT_ERROR_WISMODE_ENABLED_ON_DESTINATION_PORT,"Wismode is enabled on destination port") \
230 NT_MAKE_ERROR2(NT_ERROR_RESOURCE_IN_USE, "Resource is in use and cannot be released/re-configured") \
235 NT_MAKE_ERROR2(NT_ERROR_PORT_RANGE_OUT_OF_RANGE, "Port option must include all ports on the adapter") \
236 NT_MAKE_ERROR3(NT_ERROR_HOSTBUFFER_OUT_OF_RANGE, "Host buffer number out of range", "Host buffer number out of range: %d. Must be between %d and %d") \
237 NT_MAKE_ERROR3(NT_ERROR_INVALID_NUMANODE_RANGE, "Invalid NUMANode range", "Invalid NUMANode range: (%d..%d)") \
238 NT_MAKE_ERROR3(NT_ERROR_NUMANODE_OUT_OF_RANGE, "NUMANode out of range", "NUMANode out of range %d. Max NUMANode is %d") \
239 NT_MAKE_ERROR3(NT_ERROR_TOO_MANY_VALUES, "Too many values", "Too many values: Max %d values allowed") \
240 NT_MAKE_ERROR3(NT_ERROR_SWAPPED_RANGE, "Illegal range", "Illegal range (%d..%d). Must be swapped") \
241 NT_MAKE_ERROR3(NT_ERROR_STREAMID_OUT_OF_RANGE, "Stream ID out of range", "Stream ID out of range %d. Max Stream ID is %d") \
243 NT_MAKE_ERROR3(NT_ERROR_SOURCE_PORT_OUT_OF_RANGE, "Source port number out of range", "Source port number out of range: %d. Max port number is %d") \
244 NT_MAKE_ERROR3(NT_ERROR_DESTINATION_PORT_OUT_OF_RANGE, "Destination port number out of range", "Destination port number out of range: %d. Max port number is %d") \
245 NT_MAKE_ERROR3(NT_ERROR_PRIORITY_OUT_OF_RANGE, "Priority out of range", "Priority out of range: %d") \
246 NT_MAKE_ERROR3(NT_ERROR_TIMEOUT_OUT_OF_RANGE, "Timeout out of range", "Timeout out of range: %d. Must be between %d and %d") \
247 NT_MAKE_ERROR3(NT_ERROR_OFFSET_OUT_OF_RANGE, "Offset out of range", "Offset out of range: %d. The maximum allowed value is %d") \
248 NT_MAKE_ERROR3(NT_ERROR_ILLEGAL_COMPERATOR, "Illegal comparator used", "Illegal comparator used in \"%s\"") \
249 NT_MAKE_ERROR3(NT_ERROR_MISSING_CHAR_IN_MACRO, "Missing character in macro name", "Missing '%c' in macro name") \
250 NT_MAKE_ERROR3(NT_ERROR_ILLEGAL_CHARACTERS_IN_MACRO_NAME, "Illegal characters in macro name", "Illegal characters in macro name '%c'") \
251 NT_MAKE_ERROR3(NT_ERROR_MACRO_NAME_TOO_LONG, "Macro name is too long", "Macro name is too long: %d chars. Max length is %d chars") \
252 NT_MAKE_ERROR3(NT_ERROR_ILLEGAL_CHARACTERS_IN_MACRO_DEF, "Illegal characters in macro definition", "Illegal characters in macro definition '%c'") \
253 NT_MAKE_ERROR3(NT_ERROR_MACRO_DEF_TOO_LONG, "Macro definition is too long", "Macro definition is too long. Max length is %d") \
255 NT_MAKE_ERROR3(NT_ERROR_POWER_SWITCH_DELAY_TOO_LARGE, "Power switch delay too large", "Power switch delay too large %d. Max delay is %d") \
256 NT_MAKE_ERROR2(NT_ERROR_RESERVEDDMAPOOLSIZE_MULTIPLE_OF_4, "ReservedDMAPoolSize must be a multiple of 4") \
257 NT_MAKE_ERROR3(NT_ERROR_NUMSEGMENTS_TOO_LARGE, "NumSegments out of range", "NumSegments must be between %d and %d") \
258 NT_MAKE_ERROR3(NT_ERROR_INVALID_SEGMENT_SIZE, "Invalid segment size", "Invalid segment size. Valid values are %u, %u and %u") \
259 NT_MAKE_ERROR3(NT_ERROR_INVALID_MAX_LATENCY, "Invalid max latency", "Invalid max latency. Must be between %d and %d") \
260 NT_MAKE_ERROR2(NT_ERROR_INVALID_MAX_LATENCY2, "Invalid max latency - must be a multiple of 100") \
261 NT_MAKE_ERROR3(NT_ERROR_EXT_DESC_LENGTH_LARGE, "Extended descriptor length too large", "Extended descriptor length too large. Must be less than %d") \
262 NT_MAKE_ERROR3(NT_ERROR_TIME_SYNC_OFFSET_LARGE, "Time sync offset too large", "Time sync offset too large - must be less than %d") \
263 NT_MAKE_ERROR3(NT_ERROR_IFG_TOO_LARGE, "IFG too large", "IFG too large. Must be less than %d") \
264 NT_MAKE_ERROR3(NT_ERROR_COLOR_OUT_OF_RANGE, "Color out of range", "Color out of range: %d. Max color is %d") \
265 NT_MAKE_ERROR3(NT_ERROR_SLICEOFFSET_OUT_OF_RANGE, "Slice offset out of range", "Slice offset out of range: %d. Max frame length is %d") \
266 NT_MAKE_ERROR3(NT_ERROR_SET_DESC_PORT_OUT_OF_RANGE, "Set descriptor port out of range", "Set descriptor port out of range: %d. Max port number is: %d") \
267 NT_MAKE_ERROR3(NT_ERROR_FILENAME_TOO_LONG, "File name too long", "File name too long: %d. Max length is %d") \
268 NT_MAKE_ERROR3(NT_ERROR_HASHVALUE_OUT_OF_RANGE, "Hash value out of range", "Hash value out of range: {0x%02X:0x%02X}. Max value is 0x%02X") \
269 NT_MAKE_ERROR3(NT_ERROR_HASHSPLIT_PART_OUT_OF_RANGE, "Hash split part out of range", "Hash split part %d out of range: Must be between %d and %d") \
270 NT_MAKE_ERROR3(NT_ERROR_HASHSPLIT_VALUE_OUT_OF_RANGE, "Hash split value out of range", "Hash split value %d out of range: Must be less than %d") \
271 NT_MAKE_ERROR3(NT_ERROR_HASHSPLIT_VALUE_RANGE_ERROR, "Hash split value range is illegal", "Hash split value range (%d..%d) is illegal: Value must be less than %d and in right order") \
272 NT_MAKE_ERROR3(NT_ERROR_HASHSPLIT_VALUE_LIST_ERROR, "Hash split value illegal", "Hash split value illegal - only one value allowed") \
273 NT_MAKE_ERROR3(NT_ERROR_NUMBER_RANGE_TOO_LARGE256, "Number too large", "Number too large (%d..%d): Must be less than %d") \
274 NT_MAKE_ERROR3(NT_ERROR_NUMBER_TOO_LARGE256, "Number too large", "Number too large %d: Must be less than %d") \
275 NT_MAKE_ERROR3(NT_ERROR_TOO_MANY_EVENTS, "Too many events", "Too many events: Max %d events allowed") \
276 NT_MAKE_ERROR3(NT_ERROR_LENGTH_TOO_LARGE, "Length too large", "Length too large %d. Must be less than %d") \
277 NT_MAKE_ERROR3(NT_ERROR_DATAMASK_OUT_OF_RANGE, "Data mask out of range", "Data mask out of range [%d:%d]. Must be less or equal to %d") \
278 NT_MAKE_ERROR3(NT_ERROR_BITMASK_ILLEGAL, "Bitmask illegal", "Bitmask illegal: Second value must be less than first value [%d..%d]") \
279 NT_MAKE_ERROR3(NT_ERROR_BITMASK_ILLEGAL31, "Bitmask illegal", "Bitmask illegal: First value must be less than 31 [%d..%d]") \
280 NT_MAKE_ERROR2(NT_ERROR_MISMATCH_DATATYPE_DATAVALUE, "Mismatch between DataType and DataValue") \
281 NT_MAKE_ERROR3(NT_ERROR_DATA_OUT_OF_RANGE, "Data out of range", "Data out of range %d. Must be less or equal to %d") \
282 NT_MAKE_ERROR3(NT_ERROR_DATA_OUT_OF_RANGE_HEX, "Data out of range", "Data out of range %X. Must be less or equal to %X") \
283 NT_MAKE_ERROR3(NT_ERROR_INVALID_DATA_RANGE, "Invalid data range", "Invalid data range (%d..%d). %d must be less than %d") \
284 NT_MAKE_ERROR3(NT_ERROR_DATA_RANGE_OUT_OF_RANGE, "Data out of range", "Data out of range (%d..%d). Must be less or equal to %d") \
289 NT_MAKE_ERROR3(NT_ERROR_ILLEGAL_STRING_MUST_BE, "Illegal string", "Illegal string - must be %d characters long") \
299 NT_MAKE_ERROR2(NT_ERROR_INVALID_NO_OF_ARGS_IN_MACRO_DEF, "Invalid number of arguments in macro definition") \
300 NT_MAKE_ERROR2(NT_ERROR_MISSING_PAREN_IN_MACRO_DEF, "Missing brackets '(' or ')' in macro argument") \
306 NT_MAKE_ERROR2(NT_ERROR_BONDING_PLACEMENT, "Master and slave adapters have not been configured together") \
316 NT_MAKE_ERROR2(NT_ERROR_UNSUPPORTED_EXTENDED_DESCRIPTOR, "The extended descriptor is not supported") \
324 NT_MAKE_ERROR2(NT_ERROR_HOSTBUFFER_MIX, "host buffers from in-line and capture adapters cannot be merged in a streamid") \
326 NT_MAKE_ERROR2(NT_ERROR_HASHMASK_ALREADY_SET, "Hash mask already set for the specified hash mode") \
329 NT_MAKE_ERROR2(NT_ERROR_NO_AVAILABLE_HOSTBUFFER, "No available host buffer found matching the command") \
331 NT_MAKE_ERROR2(NT_ERROR_INLINE_SEGMENT_CONFLICT, "The segment interface cannot be used with in-line adapters") \
340 NT_MAKE_ERROR2(NT_ERROR_INVALID_PACKET_SIZE, "Invalid packet size - length must be 8 bytes aligned") \
352 NT_MAKE_ERROR2(NT_ERROR_NTAPI_NET_TX_PORTS_INVALID, "Some TX ports specified in TX mask are invalid") \
356 NT_MAKE_ERROR2(NT_ERROR_NTAPI_NET_TX_TSI_NOT_SUPPORTED , "Timestamp inject configured but not supported") \
357 NT_MAKE_ERROR2(NT_ERROR_NTAPI_NET_TX_L3_L4_CS_NOT_SUPPORTED , "Calculation of L3 and L4 checksum configured but not supported") \
358 NT_MAKE_ERROR2(NT_ERROR_NTAPI_NET_FCS_NOT_SUPPORTED , "Calculation of FCS checksum configured but not supported") \
359 NT_MAKE_ERROR2(NT_ERROR_NTAPI_STAT_GET_FAILED, "Could not receive updated statistics in a reasonable time") \
360 NT_MAKE_ERROR2(NT_ERROR_NTAPI_STAT_GET_INVALID_CMD, "NT_StatRead called with unknown command") \
361 NT_MAKE_ERROR2(NT_ERROR_NTAPI_SYSTEM_NULL_STREAM, "NT_System stream is NULL - call NT_Open to create a stream") \
363 NT_MAKE_ERROR2(NT_ERROR_NTAPI_SYSTEM_READ_INVALID_CMD, "NT_SystemRead called with unknown command") \
364 NT_MAKE_ERROR2(NT_ERROR_NTAPI_SYSTEM_READ_NO_VPD_SUPPORT, "NT_SystemRead VPD requested, but not supported") \
365 NT_MAKE_ERROR2(NT_ERROR_NTAPI_NET_RELEASE_INVALID_BUF, "Tried to release an invalid buffer - timed out NetxxGet call must not be released") \
366 NT_MAKE_ERROR2(NT_ERROR_NTAPI_CLOSE_WITH_INUSE_BUFFERS, "NT_NetRxClose called with pending in-use buffers") \
368 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_LIMITED_MODE, "NT service running in limited mode due to initialization errors - command not permitted")\
369 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_STARTUP_FAILED_VPD, "NT service startup failed - VPD initialization failed")\
370 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_INI_FILE_BUSID_CLASH, "The ini-file contains adapters with same bus ID")\
371 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_INI_FILE_ADAPTER_MISSING,"The ini-file contains adapters not present")\
372 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_INI_FILE_ADPTERX_MISSING,"The ini-file [Adapter(x)] not found")\
376 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_HBM_NO_EMPTY_SLOT, "HBM reports no empty slot found (internal error)")\
377 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_HBM_NO_TX_HOSTBUFFER, "HBM reports no free TX host buffers found")\
378 NT_MAKE_ERROR3(NT_ERROR_NT_SERVICE_HBM_NO_TX_HOSTBUFFER_NUMA,"HBM reports no free TX host buffers found", "HBM reports no free TX host buffers found on NUMA %d (requested numa %d)")\
379 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_HBM_HOSTBUF_IDX_ERROR, "HBM failed to find host buffer index (internal error)")\
380 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_HBM_STREAMMAP_ERROR, "HBM reports no free stream maps found (internal error)")\
381 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_HBM_EGRESS_ERROR, "HBM host buffer already mapped to egress port")\
382 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_HBM_EGRESS_MAP_ERROR, "HBM error - only RX host buffers may be mapped to an egress port")\
383 NT_MAKE_ERROR2(NT_ERROR_NT_SERVICE_HBM_INIT_TOO_MANY_HB, "HBMInit: too many host buffers specified")\
386 NT_MAKE_ERROR2(NT_ERROR_ADAPTER_BONDING_READ_DAUGHTER_FAILED,"Adapter bonding: daughter board read failed")\
387 NT_MAKE_ERROR2(NT_ERROR_ADAPTER_BONDING_INLINE_ADAPTER, "Adapter bonding: In-line adapters cannot be bonded with expansion cards")\
388 NT_MAKE_ERROR2(NT_ERROR_ADAPTER_BONDING_TRAINING, "Adapter bonding: Expansion bus training failed")\
389 NT_MAKE_ERROR2(NT_ERROR_ADAPTER_BONDING_SLAVE_ALREADY_BONDED,"Adapter bonding: Slave already bonded")\
390 NT_MAKE_ERROR2(NT_ERROR_ADAPTER_BONDING_SLAVE_NOT_FOUND, "Adapter bonding: Failed to find bonded slave")\
391 NT_MAKE_ERROR2(NT_ERROR_ADAPTER_BONDING_TOO_MANY_BUFFERS, "Adapter bonding: Too many host buffers defined (Total max 32)..")\
392 NT_MAKE_ERROR2(NT_ERROR_SDRAM_INIT_FAILED, "SDRAM DDR: Initialize controller failed (internal error)")\
396 NT_MAKE_ERROR2(NT_ERROR_SDRAM_CONFIGURE_FEEDS_FAILED, "SDRAM DDR: Configure feeds failed (internal error)")\
400 NT_MAKE_ERROR2(NT_ERROR_VPD_INIT_DEFRAG_FAILED, "VPD init: Failed defragmenting sectors (internal error)")\
401 NT_MAKE_ERROR2(NT_ERROR_VPD_SUPPLIED_MEM_TOO_SMALL, "Not enough memory in buffer for VPD info")\
415 NT_MAKE_ERROR2(NT_ERROR_MERGE_NOT_ALLOWED, "Merge between different adapter types is not allowed")\
416 NT_MAKE_ERROR2(NT_ERROR_IPF_MERGE_NOT_ALLOWED, "IPF unmatched stream merge on in-line adapter not allowed")\
417 NT_MAKE_ERROR2(NT_ERROR_TX_LASER_DISABLE_NOT_SUPPORTED, "TX laser software disable is not supported")\
420 NT_MAKE_ERROR2(NT_ERROR_PACKET_IF_NOT_SUPP, "When running PCAP header, the packet interface is not supported")\
423 NT_MAKE_ERROR2(NT_ERROR_TXPORT_SAME_ADAPTER_MISMATCH, "A TX port is specified, receiving data from a capture adapter. The TX port must be on the same adapter as the receiving port(s)")\
424 NT_MAKE_ERROR2(NT_ERROR_TXPORT_INLINE_MISMATCH, "The TX port does not match an in-line adapter")\
425 NT_MAKE_ERROR2(NT_ERROR_TXPORT_PRODUCTFAMILY_MISMATCH, "The TX port does not match an adapter of same product family")\
426 NT_MAKE_ERROR2(NT_ERROR_STREAM_PROFILE_MISMATCH, "The stream cannot merge from adapters with different profiles")\
427 NT_MAKE_ERROR2(NT_ERROR_STREAM_PRODUCTFAMILY_MISMATCH, "The stream cannot merge from adapters of different product families") \
428 NT_MAKE_ERROR3(NT_ERROR_INVALID_NUMBER, "Syntax error - invalid number", "Syntax error - invalid number \"%s\"") \
429 NT_MAKE_ERROR3(NT_ERROR_HOSTBUFFERSIZE_OUT_OF_RANGE, "Host buffer size out of range", "Host buffer size %d MByte out of range - must be between %d MByte and %d MByte") \
430 NT_MAKE_ERROR2(NT_ERROR_RETRANSMIT_PORT_FILTER_NOT_ALLOWED, "Port filter is not allowed in retransmit") \
431 NT_MAKE_ERROR2(NT_ERROR_SLICE_RETX_WITHOUT_RETRANSMIT, "Cannot setup retransmit slicer without a retransmit destination port") \
432 NT_MAKE_ERROR2(NT_ERROR_PCI_BANDWIDTH_MEASUREMENT_FAILED, "The measurement of PCI bandwidth failed - please check the log") \
433 NT_MAKE_ERROR3(NT_ERROR_SENSOR_SOURCE_NOT_SUPPORTED, "Sensor source not supported", "Sensor source %d not supported") \
434 NT_MAKE_ERROR3(NT_ERROR_SENSOR_SOURCEINDEX_OUT_OF_RANGE, "Sensor source index out of range", "Sensor source index %d out of range - range is [0..%d]\n") \
435 NT_MAKE_ERROR3(NT_ERROR_SENSOR_INDEX_OUT_OF_RANGE, "Sensor index out of range", "Sensor index %d out of range - range is [0..%d]\n") \
437 NT_MAKE_ERROR2(NT_ERROR_FILEHEADER_ONLY_ON_SEGMENTS, "The file header can only be retrieved when using the segment interface") \
438 NT_MAKE_ERROR2(NT_ERROR_STREAMID_TXPORT_MISMATCH, "The number of stream IDs and TX ports do not match") \
441 NT_MAKE_ERROR2(NT_ERROR_GLOBALSYNC_MODE_NOT_SUPPORTED, "Global sync mode not supported by inline adapters") \
447 NT_MAKE_ERROR2(NT_ERROR_TIMESTAMP_INJECT_OFFSET, "Adapter does not support timestamp injection offset other than start of frame") \
448 NT_MAKE_ERROR2(NT_ERROR_GLOBAL_SYNC_INVALID, "IFG cannot be changed while in Global Sync mode") \
450 NT_MAKE_ERROR2(NT_ERROR_TX_TIMING_NOT_SUPPORTED, "TX timing cannot be changed for the adapter") \
451 NT_MAKE_ERROR2(NT_ERROR_TS_INJECT_OFF_MODE_NOT_SUPPORTED, "Timestamp injection offset mode cannt be changed for the adapter") \
453 NT_MAKE_ERROR2(NT_ERROR_DRIVER_VERSION_MISMATCH, "The kernel driver version does not match the the user mode driver") \
454 NT_MAKE_ERROR3(NT_ERROR_MASKNO_OUT_OF_RANGE, "Mask Number out of range", "Mask number %d out of range. Must be between %d and %d") \
455 NT_MAKE_ERROR2(NT_ERROR_NTAPI_NT_INIT_NOT_CALLED, "NTAPI is not initialized - NT_Init() has not been called") \
464 NT_MAKE_ERROR3(NT_ERROR_KEYLENGTH_OUT_OF_RANGE, "Key length out of range", "Key length out of range: %d. Must be less than or equal to %d") \
466 NT_MAKE_ERROR3(NT_ERROR_TOO_MANY_DESTINATION_PORTS, "Too many destination ports", "Too many destination ports: Max %d ports allowed") \
468 NT_MAKE_ERROR3(NT_ERROR_INVALID_IDENTIFIER, "Invalid identifier used", "Invalid identifier '%s' used\n") \
470 NT_MAKE_ERROR2(NT_ERROR_PCAP_NG_VERSION_NOT_SUPPORTED, "Supplied PCAP-NG file version is not supported")\
471 NT_MAKE_ERROR2(NT_ERROR_PCAP_NG_INVALID_RESOLUTION, "Invalid time stamp resolution found in PCAP-NG file")\
472 NT_MAKE_ERROR2(NT_ERROR_PCAP_NG_INVALID_PACKET_SIZE, "Invalid packet size found in PCAP-NG file")\
473 NT_MAKE_ERROR2(NT_ERROR_CAP_FILE_NOT_RECOGNIZED, "The supplied capture file format is not recognized")\
474 NT_MAKE_ERROR2(NT_ERROR_CAP_FILE_PACKET_TOO_LARGE, "Too large packets found. Captured with LRO (Large Receive Offload) enabled?")\
475 NT_MAKE_ERROR2(NT_ERROR_CAP_FILE_STORED_LENGTH_INVALID, "Packet with invalid stored length found")\
476 NT_MAKE_ERROR2(NT_ERROR_CAP_FILE_CREATION_ERROR, "Could not open target file for file format conversion")\
479 NT_MAKE_ERROR3(NT_ERROR_LENGTH_OUT_OF_RANGE, "Length out of range", "Length out of range (%d..%d)")\
480 NT_MAKE_ERROR2(NT_ERROR_MISSING_KEY_ACCESS_PARTIAL_BANK, "Bank option required for PARTIAL key access")\
481 NT_MAKE_ERROR2(NT_ERROR_MISSING_KEY_ACCESS_INVALID_BANK, "Bank option invalid for SINGLE and FULL key access")\
500 NT_MAKE_ERROR2(NT_ERROR_AVR_OPCODE_RETURNED_ERROR, "AVR Opcode did not succeed and returned an error")\